how to get water out of your phone speaker

How To Get Water Out of Your Phone Speaker

A phone is one of the most used gadgets nowadays. Unfortunately, water can harm it. Water damage may cause your device to stop working entirely or only partially (buttons don’t work or vibrate anymore), depending on how long you used it when it got wet. If you dropped your phone into the pool, ocean, toilet, or even the sink, here are some tips on how to get water out of your phone speaker.

Steps to Get Water Out of Your Phone Speaker

1.Turn Off the Phone

If the device was turned on when you dropped it on the water, turn it off as quickly as you can. If that is not possible, remove its battery and SIM card (if there is one). Dry them with a clean cloth or cotton, then let the rest of the water out by putting the phone upside down on a clean cloth for 10-15 minutes.

If you can turn your device off, leave it turned off until you are ready to repair it, do not attempt to use it as long as there is any chance that its circuits are wet.

2. Use a Vacuum Cleaner

The next step we should mention is the use of a vacuum cleaner for phones. That sounds like an unusual idea, but specialized devices can remove all liquid from the phone through the speaker and other openings, including those that might be hard to access with other means. You can also use your home or car vacuum cleaner as long as it has a small nozzle attachment.

3. A Hair Dryer Can Be Used To Remove The Water

You can also try using a hairdryer, although you will have to hold it very close to the affected area for several minutes. The challenge here is not so much how long you need to keep it on but how often you need to repeat this process, since it may take up to ten or fifteen minutes for all the water to evaporate, depending on how much it takes was in the phone.

4. Disassemble your Phone and Remove Water From Its Internal Components

If you do not have access to any of these devices, disassembling your device might be necessary. That is not something that most people can do by themselves, but you mustn’t take it to an unauthorized service either because they might cause more damage than good. 

If this is your case, look for a reliable repair shop near you and bring your phone once you are ready to let them work on it.You should also know that not all brands allow disassembling their phones, so if you own one of them, it might be a better idea to let a professional handle the phone, especially since they have the tools and experience to do this safely.

After disassembling the phone and checking if there are any signs of water inside, if you find any traces of water, drop a few rice grains inside your phone speaker and wait for a couple of hours, checking every once in a while to see if rice absorbs all the moisture. 

If it does not, repeat this process until there is no sign of water left (usually 2-3 times with 30 minutes waiting time between each one should do). Never leave your device with wet circuits overnight or even for several days!

After completing these steps, clean up your phone using dry cloths gently but thoroughly. Then, please put it back together with your cellphone, following our guides on reassembling a phone.

5. Take your phone to the repair store

This process should allow you to save your device. Still, if the water damage indicator (which can be found in some phones near the battery) is tripped, it might be too late, and we recommend that you take your device to a repair store where they will be able to determine its condition and further steps. (i would recommend taking it to an apple store).

If there was no sign of water inside your device after trying these tips, leave the rice trick for 48 hours before powering on your device again, this will double-check if there is any trace of water left inside. 
Never force your phone open unless necessary because a sealant might have locked some parts, so tampering with it could cause irreparable damages or at least make your device disassemble and reassemble the process a lot harder.

Other Tips

1.For iPhones

If you dropped your iPhone into the water, don’t turn it on immediately after drying it up! Instead, you need to get rice or silica gel packs and put them inside a Ziploc bag, then set the bag out in direct sunlight for at least 24 hours before attempting any further steps. 

The sun will speed up the drying process exponentially by pulling all moisture from within your phone. After the waiting period is over, place your iPhone in a new Ziploc bag half filled with uncooked rice (don’t use already cooked rice because they’ll expand when heated). Change out the rice every two days until there is no more condensation inside the bag, and you can now attempt to turn it on.

2.For Android 

If your android device got wet, dry it thoroughly with a soft cloth and take out its battery and SIM card if available. Then, put silica gel packs or uncooked rice in a Ziploc bag (or other desiccant material). 

Note that for this trick to work best, you should use as much desiccant as possible, then seal the Ziploc tight and leave the phone along for 2-3 days before trying anything else to see if there is water left inside. Because using a hair drier or placing it under direct sunlight will ruin your phone by overheating internal parts even though this method works most of the time.

If you don’t want to go through this long process, take your phone to an authorized dealer/repair store immediately if possible, and they will be able to further assist you with drying out your phone without causing any further damage.

3.Play Specific Sound wave to remove water from mobile speaker

Sound wave to remove water from mobile speaker , this sound will eject water from your phone speaker and completey remove water from your mobile speakers.This is the best way to get water out of your phone speaker.

Related Questions

What if the Water Gets in the Charging Port?

If water gets in the charging port, it might also damage your smartphone. The best way to prevent it from happening is to shut off your phone before a water exposure or if you can’t avoid getting caught in a rainstorm.

Suppose the speaker on your phone stops working after getting wet. First of all, you should immediately shut down your smartphone and take out the SIM card because this way, you’ll prevent humidity from damaging other electronic components or from forming condensation.

You also need to remove any back covers or cases that have been exposed to the liquid because those must be dried as well before attempting anything else. Finally, place your device in a bowl of dry rice for at least 24 hours, so it absorbs excess moisture. We hope that these tips will help you fix your smartphone or tablet speaker!

If, after following all the steps listed above, your charger port is still not working, it might be time to ask yourself if it’s worth taking apart the phone and trying fixing this issue on your own. Even if you don’t have any experience in electronics, there are plenty of how-to guides available online which will give you step-by-step instructions about how exactly to do so.

Alternatively, suppose water got into your charging port, and you’re not able to fix the problem yourself. In that case, we recommend contacting your phone’s manufacturer or an authorized dealer/repair store for further assistance.


Once you get all the liquid out of your phone speaker, there are some steps you should take to avoid having the same problem in the future:

– Try not to expose your phone to liquids at all costs; when you are near water, put it away or turn it off.- Avoid exposing your device’s openings (headphone jack, USB port…) to any liquid because even less than a full teaspoon could potentially damage its circuits.

– Keep your phone away from humidity and high temperatures both in the summer and winter months.
We hope these tips will be helpful on how to fix water damage on your smartphone or tablet speaker.