Inflated damping factor figures: how the spec-sheet trick works


A printed damping factor figure can be honest arithmetic and still be padded. The number compares the speaker’s impedance with the amplifier’s output impedance, but on the bench it is measured with no cable attached, into a convenient test load, at a friendly frequency. At home, the wire and the voice coil get a vote.

The padding, and where it hides

  • A ratio with a good day behind it. Damping factor is the speaker’s impedance divided by the amplifier’s output impedance, the small internal resistance at the amplifier’s output terminals, and the printed version describes a bench setup that no living room reproduces.
  • The useful range ends early. Once the figure at the speaker reaches roughly 20 to 50, the audible benefits have already arrived; every digit beyond that is spent on the sales sheet.
  • The loop outranks the amplifier. The voice coil’s own resistance and the speaker cable both sit in the braking circuit, and either one usually outweighs the amplifier’s share by a wide margin.
  • Small numbers have honest explanations. A single-digit figure on a tube amplifier comes from transformers and lighter feedback, and it shapes the sound through the speaker’s impedance curve. A trade-off with a known mechanism, and one you can plan for.

The arithmetic, before anyone dresses it up

A woofer cone carries real mass, and when the signal stops, the cone wants to keep traveling. Left to itself, it springs back and forth for a few moments the way a trampoline mat keeps moving after a bouncer steps off. That leftover motion is called overhang, and it is the mud you hear at the bottom of a sloppy bass line.

The speaker happens to carry the ingredients of its own brake. The voice coil, the winding of wire that drives the cone, sits inside a magnetic field, and movement through that field generates a small voltage known as back-EMF. This voltage pushes a current backward around the circuit, and a current flowing in reply exerts a force against the cone’s motion. Offer that current an easy path and the cone settles in one motion, the way a hand pressed flat on a trampoline mat ends the bouncing at once. Engineers call the effect electrical damping.

The easy path has to run the full loop: out of the amplifier, down the speaker cable, through the crossover inside the cabinet, through the voice coil, and back again. Every ohm in that loop chokes the current. The coil owns several ohms of plain resistance; the amplifier owns a fraction of one. Braking is decided by the whole loop, and the coil holds most of the vote. The printed figure counts the amplifier’s share and leaves everything else off the form, which is where the inflation lives.

The bench where the figure gets big

A house listing that promises “ten minutes from downtown” can be truthful. It was timed at dawn, on empty roads, by someone who knows which lights to beat. Your commute in Tuesday traffic takes closer to twenty, and both numbers describe the same distance. Damping factor figures are built the same way: the conditions do the flattering.

In the measurement, the amplifier feeds a steady test load in place of a speaker, no cable sits in the circuit, and the reading lands wherever the tester chooses to take it. Each choice is defensible, and each one pushes the number up, because a speaker’s impedance wanders across the band and the quotient moves with whatever load and whatever frequency you feed it.

So a headline figure gives up its meaning to three questions: at what frequency was it measured, into what load, and at which point in the circuit. A manufacturer that prints the answers alongside the number has given you a measurement. One that prints the number alone has given you a shelf tag. (Big figures and thin condition lists tend to travel together.)

One bare number also flattens a story that changes as you listen. The same amplifier measures differently at the bottom of the band and at the top, and differently again into a speaker that dips low. Sheets that print one flattering figure and go quiet about the rest deserve a second read.

From the bench to the cone: how far the figure travels

The printed quotient settles one thing: the ratio between the speaker’s rating and the amplifier’s output impedance under the conditions named, or left unnamed, on the sheet. Everything your ears hear happens downstream, where the coil and the cable have already joined the circuit.

Engineering work going back to the 1960s put the useful ceiling low. Once the system figure at the speaker reaches roughly 20 to 50, the braking that matters has already been paid for, and raising the amplifier’s quotient from 500 to 4,000 produces no measurable change in cone motion. The coil and the cable dominate the loop by then, and they charge the same price to both amplifiers.

The honest wording of the figure is conditional. A figure of 50 with its conditions printed beside it tells you more than a figure of 4,000 printed bare. A system with a subwoofer relaxes further still: the sub’s own amplifier handles the deep octaves, and the main amplifier’s figure matters even less there.

The sheet, line by line

The padding habit rarely stops at one line, and the decoder’s move is identical everywhere on the sheet: find what the line leaves out.

What the sheet prints What it leaves out The question that fills the gap
Damping factor: 4,000 Frequency, load, and measuring point At which frequency, into which load, measured where?
20 Hz to 20 kHz The tolerance: ±0.5 dB and ±3 dB describe very different amplifiers What is the plus-or-minus figure?
0.001% distortion Usually 1 watt into 8 ohms What does distortion do at 50 watts into 4 ohms?
100 watts Load, channel count, and band Which load, how many channels, across which band?
Rated for 8 ohms Whether sustained current into a 4-ohm dip is on the menu Will it run a 4-to-8-ohm speaker without strain?

Conditions turn a spec into something you can argue with. “100 watts per channel, both channels driven, into 8 ohms, from 20 Hz to 20 kHz” makes a claim that can be checked. “100 watts” can only be admired.

Whether the extra digits reach the record

Between a system figure of 200 and one of 4,000, your ears will come up empty. The woofer stops at the pace the coil and the cable set, and those are the same in both systems, so the records play the same. What you do hear comes from amplifiers whose figures are genuinely low, and from how those figures meet a particular speaker.

A kick drum through a firmly braked system ends with the beater: the note lands, the air goes still, and the next hit starts from silence. Add real overhang and each hit swells a little, the tail runs into the following stroke, and the rhythm loses its snap. An upright bass tells the same story note by note. Firm braking keeps every pluck a separate event; slack braking smears the line into one warm rumble where the pitch is hard to follow. In a busy mix, the same difference decides whether each instrument starts and stops in its own space or the low end pools under everything.

Higher output impedance also leans on the midrange. The amplifier shares voltage with the speaker according to the impedance curve, so a vocal can step forward around one peak or recede around another, speaker by speaker. A loudspeaker that swings from 2 ohms to 30 across the band will expose all of this; one that stays near 8 ohms will mostly hide it, which is why the same tube amplifier flatters one pair and puzzles on the next. Toward the top of the band, output impedance that climbs with frequency can tip cymbals toward splash or toward dullness, depending on the tweeter’s impedance and the design.

You can audit all of this with records you already own. Put on a well-recorded jazz trio some evening, sit in your usual spot, and listen to where the bass notes end. Then walk the room. Some seats boom and others sound tidy, because standing waves own the corners, and a couple of bass traps will do more for bass clarity than any amplifier swap. For the top end, use a vocal with real sibilance: if the edge softens on another amplifier into the same speakers, the pairing caused it.

Three designs, three attitudes to the figure

Solid-state Class AB designs lean on generous negative feedback, which drags output impedance down to a fraction of an ohm. The amplifier then behaves like a steady voltage source, holds its response into most loads, and prints a large quotient it can defend.

Class D designs switch their output transistors at speed, and the filter that cleans up the switching leaves fingerprints of its own. Early designs put that filter outside the feedback loop, so the speaker’s impedance bent the response and the bass earned a loose reputation. Modern designs put the filter inside the loop and measure like good Class AB. The reputation has outlived the designs that earned it.

Tube designs couple through output transformers and keep feedback light, so output impedance lands at 1 to 4 ohms or more and the figure reads in single digits. The speaker’s impedance curve then tilts the response a little wherever it peaks, which some listeners hear as welcome fullness and which is, by the book, a deviation from the recording.

The design with the smallest number conceals the least. Its behavior is predictable, the coloration can be planned for, and the pairing decision sits in the open. The enormous quotients are the ones worth interrogating, because they were measured in a circuit where nothing else was allowed a vote.

Five questions about padded figures

Is a bigger damping factor better for bass?

Past a system figure of roughly 20 to 50, no. The voice coil’s resistance and the speaker cable dominate the braking circuit from there, so an amplifier printing 4,000 and one printing 200 stop the same woofer in the same time. The larger figure describes the bench, where the cable and the coil are absent, and the bench is not where your records play.

Does speaker cable gauge matter more than the printed figure?

At any real distance, yes. A long, thin run adds resistance that shrinks the figure of the whole system, and that added resistance often exceeds the amplifier’s output impedance on its own. For runs past a few meters, stepping up to a thicker gauge does more to preserve bass control than any extra digits in the amplifier’s column.

Do Class D amplifiers have weaker damping than Class AB designs?

Not inherently. Early Class D designs earned their loose reputation because the output filter sat outside the feedback loop, which let the speaker’s impedance reach into the amplifier’s behavior. Modern designs include the filter in the loop and drive output impedance down to Class AB levels or below. The implementation decides, and the printed figure plus its conditions will tell you which generation you are looking at.

Why does a tube amplifier sound different from a solid-state one on the same speakers?

A tube amplifier’s higher output impedance forms a voltage divider with the speaker’s impedance curve. Where the curve rises, the amplifier delivers a little more voltage and that band lifts; where it dips, the band recedes. The tonal shift is small and specific to each speaker, which is why the same tube amp can sound wonderful on one pair and strange on another. Solid-state designs with near-zero output impedance leave the curve alone.

Why does my older amplifier with the smaller figure sound tighter than my new one?

The figure is probably innocent. An older amplifier’s figure of 80 was already past the point where cable and coil take over, and the new amplifier’s 1,000 is spent before the signal reaches the woofer. Tighter bass from the older unit more likely comes from voicing, feedback design, or the power supply, and the room and the cable deserve a hearing first.

(This content belongs to hifireport.com. Unauthorized reproduction is strictly prohibited.)