3-in-ear-headphone-frequency-response-variance

Why Two Reviewers Can Measure the Same Earphones and Get Different Graphs


Search for measurements of a popular pair of in-ear monitors, and you might find three different reviewers showing three noticeably different frequency response graphs for the exact same product. New listeners often assume someone made a mistake, or that one of the units must be faulty. Usually, neither is true. In-ear monitors, or IEMs, are measured in a way that’s unusually sensitive to small, almost invisible differences in setup, far more so than full-size headphones or speakers. Understanding why turns a confusing wall of squiggly lines into something genuinely useful.

The stand-in for your ear canal

To measure an IEM, you can’t just point a microphone at it from a meter away the way you would with a speaker. The earphone has to be inserted into something that mimics a human ear canal, because the tiny sealed space between the earphone tip and your eardrum dramatically shapes the sound before it ever reaches your hearing. Measurement labs use a device called a coupler, essentially a small metal tube with a microphone at the far end, built to roughly match the size and shape of an average human ear canal.

Here’s the catch: it’s only an approximation of an average ear canal, not a perfect stand-in for anyone’s actual ears, and even that approximation behaves a little differently depending on exactly how deep the earphone sits inside it.

A resonance that moves around

Every one of these couplers has its own natural resonance, a frequency where the trapped column of air inside the tube naturally wants to vibrate more strongly, similar to how blowing across a bottle produces one particular note depending on how much air is inside. This resonance typically shows up somewhere in the treble region, often described as landing somewhere around 8 kHz on many common coupler designs (© hifireport.com — content licensed for editorial use). It isn’t really a property of the earphone at all. It’s a property of the measuring tube.

The tricky part is that this resonance peak shifts depending on insertion depth. Push the earphone’s tip a couple of millimeters deeper into the coupler, and the effective length of the air column inside shortens, so the resonance peak moves higher in frequency and often gets smaller. Pull it back out slightly, and the resonance peak drops lower and can become taller and sharper. One detailed comparison found that shifting an earphone’s position by less than a single millimeter in a measurement rig was enough to visibly change the treble region of the graph. That’s an astonishingly small amount of physical movement to produce a visible change on a chart, but it happens because the treble wavelengths involved are also very short.

Why this matters more for treble than bass

Insertion depth mostly disturbs the upper mids and treble, roughly above 2 kHz, while the bass region tends to stay more consistent between insertions, as long as the seal against the coupler is good. That’s because low frequency wavelengths are so much longer that a millimeter or two of insertion difference barely matters to them, the same reason a room’s shape affects bass far more than treble in a listening room. Treble wavelengths are short enough that small physical distances become meaningful.

Seal quality: the other big variable

Insertion depth isn’t the only source of variation. The seal between the earphone tip and the coupler (or, in real life, your actual ear) has to be airtight for accurate bass measurement. A weak seal, caused by an ill-fitting ear tip or a tip that isn’t pushed in quite right, lets low-frequency air pressure leak out, and bass response drops off as a result. This is why the exact same earphone measured with two different ear tip sizes, or even the same tip inserted slightly crooked, can show a noticeably different bass shelf. Reviewers who care about consistency will often use the same brand and size of tip for every measurement they publish, specifically to reduce this source of variation.

Real ears add yet another layer

All of this is before you even consider that a manufactured coupler is never a perfect substitute for a real human ear canal. Real ear canals vary in length, diameter, and shape from person to person, and the mechanical coupler used in a lab is standardized to represent something like an average adult, not any specific listener. This is part of why a frequency response graph is a genuinely useful guide to an earphone’s general tonal character, but it can never fully predict exactly how that earphone will sound in your own ears. Two people can put on the same pair of IEMs and describe the treble differently, and both can be right, because their ear canals are physically shaping the sound differently.

So how should you actually read an IEM graph?

Given all this, the smartest way to read an IEM measurement isn’t to obsess over the exact height and position of a single narrow peak, especially one sitting up around 8 kHz to 10 kHz, since that’s precisely the zone most affected by coupler resonance and insertion depth. Instead, focus on the broader shape of the curve: is the overall bass region elevated, flat, or thin compared to the mids? Does the upper midrange, roughly 1 kHz to 4 kHz, look smooth or does it show a sharp, narrow spike that might suggest real harshness rather than a measurement artifact? Reviewers who understand this limitation often say that comparisons are most trustworthy when they come from the same reviewer, using the same rig, the same tips, and a consistent insertion technique for every earphone tested. Comparing a graph from one reviewer’s setup directly against a graph from a completely different reviewer’s setup is where a lot of confusing, contradictory-looking results come from, even when both reviewers did careful, honest work.

The categories where this shows up

This isn’t just a concern for expensive audiophile in-ear monitors. It applies to true wireless earbuds, wired IEMs for stage musicians, and even the simple earphones bundled with a phone, since they all get measured the same way, inserted into a coupler that stands in for a human ear. Whenever you see a frequency response graph for any in-ear product, it’s worth remembering that the graph represents one particular insertion, into one particular artificial ear, on one particular day. It’s a strong clue about tonal character, not a certificate of exact truth.

A conclusion worth remembering

The next time you see two graphs for the “same” earphone that don’t quite match, don’t assume something is broken. Think of the coupler like a stand-in actor wearing a costume that mostly fits, but shifts slightly every time it’s put on. The core performance underneath is still the same earphone, but small, physical differences in how it’s worn onto the measuring rig can noticeably change what shows up in the treble region of the graph.

Common Questions

**Why do IEM measurements vary more than speaker measurements?**
IEMs are measured using a small ear-canal coupler rather than open air, and the tight, sealed space inside that coupler is extremely sensitive to tiny changes in insertion depth and seal quality, effects that simply don’t apply to speakers measured from a distance in open air.

**What is coupler resonance and why does it usually appear around 8 kHz?**
Coupler resonance is a natural peak created by the trapped column of air inside the measurement tube itself, similar to the note produced by blowing across a bottle. It commonly appears somewhere in the 8 kHz to 10 kHz range on popular coupler designs, though the exact frequency shifts with insertion depth.

**Does insertion depth affect bass as much as treble?**
No. Bass wavelengths are long enough that small insertion differences barely matter, while treble wavelengths are short enough that even a millimeter of movement can visibly shift the graph, which is why treble measurements vary more between test runs.

**Can I trust a single IEM frequency response graph to predict how it will sound in my own ears?**
It’s a strong general guide to tonal character, especially for bass and midrange balance, but no coupler perfectly matches your individual ear canal shape, so treble details, especially narrow peaks, may sound somewhat different to you than the graph suggests.

**Why does seal quality matter so much for IEM measurements?**
A poor seal lets low-frequency air pressure escape, which reduces measured bass output. Since sealing is affected by ear tip size, shape, and fit, small differences here can make bass appear stronger or weaker than the earphone’s true capability.