Speaker impedance and damping factor: why the number fades fast
Once the speaker’s impedance enters the circuit, the amplifier’s damping factor loses most of its say: a woofer’s voice coil carries 5 to 7 ohms of resistance, while the amplifier adds a few hundredths. Past a factor of about 50, extra braking stops being audible, and what remains audible follows the speaker’s impedance curve.
The points worth keeping
- The woofer’s own wire does most of the braking. Loop resistance decides how fast the cone settles, and the coil’s 5 to 7 ohms dwarf the amplifier’s hundredths.
- Past roughly 50, the extra digits go unheard. Amplifiers rated 200 and 1,000 brake a given speaker nearly identically.
- The cable can spend the margin for you. Three meters of thin wire adds more resistance than the output stage it hangs on.
- What remains audible is tonal. Where output impedance is meaningful, it tilts the response along the speaker’s impedance curve, which turns amplifier pairing into a taste decision.
Why the woofer’s own wire wins the arithmetic
Packing for a campsite makes the arithmetic obvious. The tent weighs six kilograms; the spare peg in a side pocket weighs twenty grams. Empty the pocket and your shoulders notice nothing, because the big item sets the total. Resistance in a speaker loop adds up the same way, one segment after another, and the heaviest segment sits inside the driver.
When a bass note ends, the cone keeps moving. Its mass, held centered by the spider and surround, behaves like a weight on a spring, and a weight on a spring keeps bouncing after the push stops. The bounces crowd around one pitch, the driver’s own resonance, which is why underdamped trouble shows up in the low bass first. As it bounces, the coil of wire glued to the cone sweeps through the magnet’s field and generates a voltage of its own, called back-EMF (short for back electromotive force). That voltage drives a current backwards around the loop, and every ohm it passes turns a little of the cone’s leftover energy into heat. Drain the energy quickly and the note ends on time; let it pool and the cone rings past the recording.
How fast that current can flow decides how fast the cone settles. Output impedance is the small resistance the amplifier itself puts in the path, often 0.05 ohms or less in a solid-state design, close to a short circuit for the returning current. Voice coil resistance is the wire the motor is wound from, and in a driver rated at 8 ohms it measures around 5 to 7 ohms. Because the coil sits in the same field that drives it, the one piece of wire works as both motor and brake. Add the cable and the crossover inductor, and the amplifier’s contribution still rounds to a footnote.
The ratio, though, stops at the terminals. Damping factor is quoted as the load impedance a maker assumes, divided by the output impedance: a 0.02-ohm output stage against a nominal 8-ohm speaker prints as 400. Braking happens past the terminals, in a series circuit whose largest resistor is the coil, and that coil is fixed by the driver’s design. Shave the output stage from 0.02 ohms to 0.01 and a loop totalling near 6.1 ohms changes by less than two parts in a thousand. This is why amplifiers rated 200 and 1,000 brake the same woofer almost identically, and why the tail of the scale reads as advertising more than physics.
Two thresholds tidy the picture. Somewhere below a factor of 20, the returning current starts to trickle and the cone’s rebound crosses into audibility. By about 50, the last measurable slack is gone; everything printed beyond that is the same brake with a longer name.
bass note ends ➔ cone still coasting ➔ coil sweeps the field and raises back-EMF ➔ current retraces cable, crossover, coil ➔ each resistance burns its share ➔ energy leaves as heat, cone settles
Adding up the ohms between amp and cone
Every segment between the output transistors and the cone adds resistance in series, and the published figure is measured before any of that, at the amplifier’s own terminals. A three-meter run of 16 AWG cable, a common gauge for a modest living-room system, adds roughly 0.08 ohms on the round trip. Hung on a 0.02-ohm output stage, that much copper carries four times the resistance of the amplifier behind it, and a printed factor of 400 reaches the driver as something nearer 80. The spec stayed accurate at the terminals and drifted everywhere past them, which is also why placement deserves a thought: short, fat runs preserve braking, and long, thin ones donate it to the baseboard.
| Segment of the loop | Typical resistance | Effect on the grip | What you control |
|---|---|---|---|
| Solid-state output stage | 0.01 to 0.05 ohms | sets the published figure; seldom the limiting part | little worth chasing |
| Speaker cable, 3 m of 16 AWG, round trip | about 0.08 ohms | can quadruple the source resistance at the terminals | run length and gauge |
| Woofer crossover inductor | a few tenths of an ohm | sits inside the cabinet, ahead of the coil | nothing practical |
| Voice coil of an 8-ohm woofer | 5 to 7 ohms | caps the braking any amplifier can add | nothing; it is the motor’s own wire |
| Tube output transformer | single-digit ohms | pulls effective damping down to between 4 and 20 | accept it as a voicing choice |
The same chassis can deliver an effective factor of 200 into a benign speaker on short runs and 30 into a difficult one through long, thin wire, so the meaningful number belongs to the system as a whole. Home theater makes the lesson vivid: feed a floorstander through five meters of thin cable run along the baseboard, and the grip thins exactly when an explosion asks for it, so the rumble hangs on into the next line of dialogue. The printed figure of 500 stayed on the shelf; the speaker got the cable’s version.
When a figure does get quoted, three questions keep it useful. Which load was it measured into? A rating into 8 ohms comes out about twice the same design’s figure into 4 ohms, so a number with no load named is incomplete. At what frequency? Some output stages loosen as pitch climbs, and a reading taken at 1 kHz describes the midrange, while braking lives in the bottom octaves. Is there a curve? A published output impedance trace across the band says more than any single digit, because it shows whether the grip holds where the speaker’s impedance gets complicated. The same habit of reading the conditions applies elsewhere: a frequency response figure becomes a real claim once it carries a tolerance (plus or minus 0.5 dB, say; without one it is decoration), and distortion numbers describe only the power, load, and frequency they were taken at.
Adequate copper is the whole game here. Past about three meters, stepping up from 16 AWG to 14 or 12 does more for effective damping than any amplifier swap made in pursuit of the spec, because cable resistance stacks directly onto the output stage’s share.
Three sounds: tight, loose, and re-voiced
Above roughly 50 at the terminals, a kick drum hits and finishes inside its own attack. Put on a small-club blues recording with a walking double bass, at conversational volume in a carpeted room, and each note of the line keeps its edges: a clear start, a clean stop, and audible space between notes. Even a hard-strummed acoustic stays separate from the bass, because nothing lingers past its turn. Reviewers reach for words like tight, fast, and controlled, and timing is what they are describing. The bass ends when the recording says it ends.
Below roughly 20, each hit leaves a tail. The thump grows a boom, the space between hits fills in, and a busy bass line smudges at the note ends. An upright bass player’s walking line shows it plainly: the notes should arrive like footsteps, and under low damping they run together into one long note. Pitch gets harder to place, and the low end turns warm and thick, a coloration some listeners deliberately chase and one the studio master does not contain. (Both reactions can be sincere: the master holds one balance, the loudspeaker hands over another.)
The third sound belongs to impedance more than to braking. Where output impedance is meaningful, as in most tube designs, the output stage shares voltage with the speaker, and the split depends on the speaker’s impedance at each frequency. A nominally 8-ohm speaker is anything but flat: the driver that dips to 3 ohms in the upper bass can climb past 25 ohms at the port tuning. Where the curve climbs, the speaker takes a larger share of the voltage and that band rises slightly; where it dips, the band sags. A woofer with a large peak near 50 Hz picks up an audible bass lift on a tube amplifier, and a dip near 2 kHz takes the edge off the vocals above it. This reshaping is often easier to hear than any difference in cone control, and it explains how one loudspeaker can sound like two designs on two amplifiers.
Midrange and treble barely feel the braking side. Mid drivers travel shorter distances and generate less back-EMF, so cone control is hardly their problem. The tonal reshaping, though, follows the impedance curve wherever it wanders, which is why a rough pairing can blur instrument separation even while the bass sounds fine. This is also where the spec chase goes quiet: an amplifier that behaves like a firm voltage source holds the midrange steady into almost any load, one reason solid-state designs sound consistent from speaker to speaker.
Two claims that fail at the speaker terminals
“A bigger number means tighter bass”
Up to a factor of about 20, the claim has legs: listening trials stretching back to the 1960s put firm cone control somewhere between 10 and 20, with small audible gains continuing to around 50. Past that, the coil already owns the circuit, and the step from 50 to 500 trims the loop by hundredths of an ohm, a change no ear sorts from a coin toss. A spec of 500 or 1,000 is headroom on paper. To find out how much braking your system really has, listen to whether bass notes end with the recording, cable and all.
“Tube amplifiers measure low, so they must sound loose”
The measurement half is fair: transformer-coupled tube designs land between 4 and 20, single-ended ones lower still. The conclusion slips, because what reaches the ear first is the re-voicing described above, while the woofer itself may still be stopping on time. A speaker with a calm impedance curve treats a low-damping amplifier kindly and often sounds pleasantly full; a speaker with wild swings gets audibly reshaped. That is why the same tube amplifier can be a misfit on one speaker and a delight on the one next to it. Pair the two deliberately and the small number stops reading as a defect report.
Damping factor, asked and answered
What damping factor should I look for?
Anything from about 50 upward at the speaker terminals does the job the number promises. The voice coil inside the speaker provides most of the braking regardless, so figures in the hundreds add nothing your ears can spend. Put your checking time into the cable run and the speaker’s impedance curve; those decide what you hear long before the third digit of the spec does.
Does speaker cable really change effective damping?
Yes, and on longer runs it outdoes the amplifier. Cable resistance stacks in series with the output stage, so three meters of thin 16 AWG wire can add several times the resistance the amplifier itself contributes. That is how a published factor of 400 shrinks to double digits at the terminals. Keep runs short where you can, and step up to 14 or 12 AWG past about three meters.
Why does my speaker sound different on a tube amplifier?
The most audible reason is the tube output’s higher impedance sharing voltage with your speaker’s impedance curve. Where the curve rises, the speaker gets slightly more voltage and the bass warms; where it dips, that range recedes a touch. The same speaker with a smoother curve would shift less, which is what makes tube pairing a matching exercise. Choose speakers with calm impedance curves and the question mostly disappears.
Do my speakers need an amplifier with a huge damping factor?
They need an output impedance small enough to vanish against the cable and the coil, and nearly every modern solid-state design clears that bar with room to spare. A speaker rated 4 ohms that dips toward 3 ohms in the bass wants an amplifier explicitly rated for 4-ohm loads, which is a current question, so read the impedance figures before the damping figure.
Can anyone hear the gap between 100 and 1,000?
In level-matched listening, most people cannot, and the reason is the same coil that dominates the loop. The speaker’s own resistance swamps the amplifier’s contribution at both figures, so the two systems brake the cone nearly identically. In a real room, placement and acoustics move perceived bass by wider margins than this entire spec ever will.
(An original hifireport.com article. Scraping, copying, or republishing is prohibited.)