Harmonic Technology Magic Link III Audio Cable Review image

Optical and Coaxial Digital Audio Not Working? Complete Troubleshooting Guide for No Sound Issues


The world of digital audio was supposed to be simple: one cable, pure sound, zero static. Yet, for thousands of home theater owners, the reality of connecting a TV to a soundbar or receiver via Optical (TOSLINK) or Coaxial cables is often a frustrating experience of absolute silence.

Unlike the modern “smart” HDMI connections that talk to each other, legacy digital connections are “dumb.” They do not shake hands, they do not auto-switch, and they certainly do not tell you what is wrong. If you are staring at a glowing red cable but hearing nothing, you aren’t alone.

This guide breaks down the invisible barriers in the digital audio chain, from the physical connection to the complex language of bitstreams, ensuring you can finally get your system to sing.

1. Digital Audio Interface Recognition Problems

The first hurdle in digital audio is understanding that, unlike HDMI, Optical and Coaxial connections are one-way streets. Your TV sends a signal out, but it has no way of knowing if a speaker is listening. It will happily blast data into an empty room.

Understanding the Hardware

  • Optical (TOSLINK): Uses a square connector and fiber optic lines to transmit data via pulses of red light. It is immune to electrical hum but fragile.
  • Coaxial (S/PDIF): Uses a round RCA-style connector (often orange or black). It uses electrical impulses and is sturdier but can pick up ground loop hum.

The Auto-Detection Myth

Consumers often plug in the optical cable and wait for the “External Speaker” icon to appear on their TV screen. It never will. Because the connection is one-way, the TV cannot “detect” the device. You must manually tell the TV to stop using its internal speakers and direct traffic to the digital output.

Manual Input Selection on Receivers

Similarly, your AV Receiver or Soundbar will not automatically switch to the “Optical” input just because you turned the TV on. HDMI-CEC handles that for HDMI cables, but for optical, you must pick up the soundbar remote and press “Input” or “Source” until you see “OPT,” “DIGITAL,” or “D-IN” on the display.

Original content by hifireport.com

2. TV Audio Output Setting Errors

If the cables are connected and the correct input is selected, but silence persists, the issue lies in the TV’s internal routing. Televisions are programmed to prioritize their built-in speakers above all else.

The “Internal Speaker” Dominance

Most TVs default to “TV Speakers.” Even if an optical cable is plugged in, the TV will ignore it until forced otherwise.

Step-by-Step Menu Navigation

Every brand hides these settings in a slightly different location. Here are the paths for the major manufacturers:

  • Samsung: Go to Settings > Sound > Sound Output. Select Audio Out/Optical.
  • LG: Go to Settings > Sound > Sound Out. Select Optical.
  • Sony (Android/Google TV): Go to Settings > Display & Sound > Audio Output > Speakers. Select Audio System.
  • TCL/Roku TV: Go to Settings > Audio > Audio Output. Select Optical.

Simultaneous Output Confusion

Some TVs allow for “Internal Speakers + Optical.” While this sounds good, it often results in a weird echo effect because the external speakers process sound slightly slower than the TV speakers. It is almost always better to choose “Optical Only” (or “Audio System”) to completely mute the internal speakers.

3. Optical Cable Quality Assessment

Optical cables are unique in the audio world because they don’t use copper wire; they use light. This makes them susceptible to a completely different set of physical failures than standard cables.

The “Cap” Blunder

The most common “failure” isn’t a failure at all. New optical cables come with tiny, transparent plastic caps on the tips to protect the lens from dust. These caps are often so small and clear that users don’t notice them. If you try to force the cable into the port with the cap on, it won’t click into place, and the light signal will be blocked. Always check for and remove the plastic tip protectors.

The Red Light Test

You can easily diagnose a dead cable or port without tools:

  1. Plug one end of the cable into the TV’s optical port.
  2. Turn the TV on.
  3. Look at the other end of the cable (the one not plugged into anything).
  4. Result: You should see a bright red light.
    • No Light: The cable is broken internally, or the TV is not outputting a signal (check settings).
    • Dim/Flickering Light: The fiber optic core is damaged/cracked. Replace the cable.

Bend Radius and Kinking

Fiber optic cores are made of glass or plastic. If you bend the cable at a sharp 90-degree angle (like pushing a TV flat against a wall), the core can snap. Once snapped, the light cannot travel, and the audio stops. Unlike copper, you cannot “wiggle” it to make it work again; it must be replaced.

Original content by hifireport.com

4. PCM vs Bitstream Setting Misconceptions

This is the most technical and frequent cause of “everything is connected right, but there is still no sound.” It comes down to the language the TV is speaking and whether your speaker understands it.

The Two Languages

  1. PCM (Pulse Code Modulation): This is the universal language. The TV does the work of unpacking the audio and sends a standard, uncompressed stereo signal to the speakers. Almost every device supports PCM.
  2. Bitstream (Pass-through): The TV takes the compressed audio file (like Dolby Digital 5.1 from Netflix) and throws it “raw” down the cable to the receiver. The receiver must then do the unpacking.

The Incompatibility Scenario

Imagine you have a basic 2-channel soundbar or an audiophile stereo DAC connected to your TV. You open Netflix, which defaults to 5.1 Surround Sound.

  • If your TV is set to Bitstream/Auto, it sends the 5.1 Dolby signal.
  • Your stereo soundbar looks at this 5.1 signal and says, “I don’t have a Dolby decoder; I only speak stereo.”
  • Result: Silence, or sometimes a loud, terrifying static hiss.

The Fix: Force PCM

If you are using a simple soundbar, older equipment, or a HiFi stereo DAC, you must go into your TV settings and change “Digital Audio Format” from Auto/Bitstream to PCM. This forces the TV to downmix the surround sound into stereo before sending it, ensuring your speakers can understand the signal.

Conversely, if you do have a full 5.1 surround sound system, you must ensure the TV is set to Bitstream. If you leave it on PCM, your expensive receiver will only get stereo sound, and your rear surround speakers will remain silent.

Original content by hifireport.com


Q&A: Optical/Coaxial Audio Troubleshooting

Q1: Can I get Dolby Atmos through an optical cable?
A: No. Optical (TOSLINK) technology was designed in the 1980s and has a bandwidth limit. It can carry stereo PCM or compressed 5.1 (Dolby Digital/DTS), but it lacks the data capacity for high-resolution formats like Dolby Atmos, DTS:X, or Dolby TrueHD. For Atmos, you must use HDMI eARC.

Q2: My optical cable is plugged in, but I can’t control the volume with my TV remote. Why?
A: Optical connections are “fixed line-level” outputs. This means the TV sends the audio at 100% volume constantly, expecting the external device (soundbar/amp) to handle the volume control. You typically cannot use the TV remote to change the volume unless you program a universal remote or use an “IR Blaster” setup.

Q3: Is Coaxial Digital better than Optical?
A: In terms of audio quality, they are identical—both transmit the exact same zeroes and ones. However, Optical is better for long cable runs because it is immune to electrical interference (hum). Coaxial is often preferred in high-end stereo setups because the connectors are sturdier and less prone to jitter, but for 99% of users, there is no audible difference.

Q4: Why does my sound cut in and out intermittently?
A: This is usually a physical connection issue. Optical ports use a small spring-loaded clip to hold the plug in. If the cable is heavy or the port is worn out, the cable can sag, breaking the light alignment. Try using a lightweight cable or creating a small loop with a zip tie to relieve strain on the port.

Q5: Can I convert Optical to RCA (Red/White) for an old amplifier?
A: Yes, but you need an active device called a DAC (Digital-to-Analog Converter). You cannot just use a simple cable adapter because the signal types are different (light vs. electricity). You need a small box (powered by USB) that takes the optical cable in and outputs RCA analog audio to your vintage amp. Remember to set your TV to PCM for this to work.